Відео

What kind of oil did you use mate?

Nice use of wood blocks to raise vehicle a bit, to get clearance.

Can you use additional filters, such as cut to size electrostatic portable AC filters on this model? Would a HEPA filter be too much blockage? Can mold or bacteria, etc develop inside these or is the coils too hot for it to survive, as in making using a filter pointless ? Thanks in advance anyone!

You obviously don’t realize the plunger has a lock release.

Will this help with extremely dry nostrils? I have dry, irritated nostrils from allergies

Oh dear, I am not mechanically inclined but mine is not cutting well at this point. I also watched the sharpening video. Will try to do this. If I can't get it to work, will either have to go back to gas powered mower or borrow a goat :( Thank you for the instruction,

1:04 You said ‘hard on, pump your grease into it’.

Done this meany times before but ended up getting stoned before hand and completely forgot. Cheers dude.

¡¡Thanks!!

Thanks for the video. I also do work on top of the washer and dryer, and sometimes the chest freezer, when my wife isn’t home. 😂

So what is this doing? It forces water vapor out of the engine instead of sitting in the oil case?

Thank you Sir 🎉

Great video and advice from reading comments. Too many take this mixture for granted.

Damn this video save my day !!! Mine was absolutly naaaasty. But i have an issue with my water level sensor that is completly jammed in deposit and residue, how do we get a better access to clean the water pan and sensor ??

Yes, it’s done exactly like this except mine did not have that much slack and was hard to twist and pull of there. The left side was easy but the right side took 20+ min to finally get right

Huge help. Thanks man!

Thank you for you video. I recently got this older model and was happy that a video was online to help me.

This is great - I've been thinking about something like this for fine detail trimming

What do you do when the grease appears to not go into the fitting but squeezes out around it? Tighten it more?

Thank you!

WOW I was going crazy rereading the manual and no where did it mentioned how that released worked. This video saved my sanity. Keep doing what you're doing! THANK YOU!

Thank you, I am glad that my hydraulic floor jack now works as it's supposed to do. I just didn't know how. 😅

It seems ridiculous, since I sharpen my carving knives all the time with no problem, yet I'm frustrated that my side cutters seem so dull and think about sharpening them but never do. 🤣😂

What if the not problem end breaks, i just changed mine but i feel its gonna need some work on top of that

Cool! Thanks for sharing this.

Can you tell me how to fix the bottom half of plate, it’s off I have it taped down. Any help would be appreciated. Thank you.

Nothing gets passed the vapor filters, everyone should buy one...

Thanks for making your video! Quite helpful!

Thanks!

That's the breather line, where air is supposed to go into the engine. The pcv line is on the opposite side...

Ghetto bike trainer 😂 11/10

Should it dry before placing back in?

Just cleaned mine but my check engine light is still on?

Depending on the model of ac you have, you might find success just clearing the dust from the fins with a dry toothbrush and no cleaning solution. Just be gentle to not bend the fins. Increased the air flow and cooling by 3x when I cleaned mine. I was afraid to go all in with taking it apart and getting it wet like the method shown in this video because of where the electronics are located in mine.

It’s never that easy with a flathead, get the pry tool !

Hello. My floor jack is leaking oil from the release valve. Is there a fix for this? Thank you very much for your videos.

I have a slightly different style floating caliper where the pads have ears that slide along these pins on a caliper carrier. But my issue I think I the same. They are somehow jumping when I brake. So much to the point where I took the pads off and inspected and one of the inner pads had an actual lip. Any way to fix this on my setup? I’ve tried new pads and rotors and the issue remains. The car is a Mercedes e class

Nice! I’m a new subscriber. Love your video’s. You are straight to the point and explain things that I can do lol. Thanks keep up the good work👌🏼

Water alcohol injection works the best for cleaning pistons and valves

How long did it take you from start to finish?

Thanks for the help.

Thank man! I was about to throw mine.

I got a 1 long beep that lasted for 2-3mins..what does that mean?

Can I use that same procedure to merge the pipes together if broken? Thanks

Never showed the steering wheel straightened out afterwards so I say bogus..

Just a heads up, if you get a wire wheel built for a die grinder, you won't have that problem. You are using cramped wire wheels that are only rated for 4,000 to 4,500 rpm, not wheels that are built for 20,000 to 25,000 rpm.

I once brought a traverse had no bolts was just holding with the caliper tension and it rattle and felt like hell assuming that's why I got it cheap fixed it under 20 dollars

Very informative and to the point, thank you for this.

Why the top thread is breaking while switching

I've never been able to get more than 12.9 gal. In the 14.9 gal tank, normal?